How Much Water To Add To Brine Tank After Cleaning

Video Transcript

Gary The Water Guy:
Hi. I'm Gary the Water Guy, and I ain The Water Filter eStore and The Water Store in Midland, Ontario.

Gary The H2o Guy:
Later you've had your water softener for a few years, you may discover inside the alkali tank that in that location's a blackness band and there's some other black stuff along the sides. Yep. That's mold. We can see the mold stains around the outside and the black ring, and that'due south what we want to get rid of. Information technology'southward a good idea to remove that, to clean that out, so you lot get a nice, fresh start.

Gary The H2o Guy:
At present, there'southward a couple of dissimilar kinds of water softeners. There's a post-fill water softer like this Ballyhoo valve here, which means there'southward h2o in with the table salt to make the brine, or there's a pre-fill water softener. If yous come across, there's no water in with the salt. That ways it's a pre-make full. Those ones are a little flake easier to clean out. Basically, you merely remove the salt, you clean inside the brine tank. You tin can use dish-washing lather. Or if the mold stains are quite pregnant, you can utilise something like this, The Ultimate Mold Eliminator. And then you lot refill it with table salt and you're good to go. With a post-fill up i like this, yous have to remove the h2o outset. You tin can either use a shop vac, or if you want to do it a little fleck easier and eliminate the step of the shop vac, you lot can actually put it into a regen cycle. With the alkali wheel, information technology'll draw the water out of the unit itself, and that'll brand it a little scrap easier.

Gary The Water Guy:
We tin put this h2o softener into regen mode simply by holding down the regen button for five seconds. The showtime phase that it goes into is the backwash cycle. Once it starts counting downward, once the cycle'south actually begun the timing, then we can advance to the side by side cycle. We press the button again, we go into the brine cycle, and over again, once it starts counting down, it'south going to suck all the water out of the alkali tank and information technology makes it a lot easier to clean. Like I say, either you can practice it this way, or information technology can utilise the shop vac. Then when you're washed, when it'southward gone through the cycle, you can advance it through the rest of the cycles. Once again, once it starts counting down, that's when you lot can advance it to the next 1. And then take information technology back to abode. Only for this particular process, we desire to make sure we leave it on that alkali cycle for the full 60 minutes. That way, it'll draw all the water out and brand it a lot easier to clean out the brine tank.

Gary The Water Guy:
In one case you've washed that, again, you need to clean information technology out, put new salt. With the post-fill ones, you're going to have to add together iii gallons of h2o, fix information technology to regenerate that night, and it'll go through the whole procedure, clean itself, and y'all'll exist back a hundred percentage in service over again the next day.

Gary The Water Guy:
Our newly cleaned brine tank topped upward with salt and water. If yous like what you lot saw today, please click the subscribe button. That way, you'll be notified nigh any new videos that get available on this channel. If y'all want to become some more data, y'all can become to our website, either thewaterstoremidland.com or thewaterfilterestore.com.

Again, I'thousand Gary the H2o Guy from The Water Shop in Midland, Ontario. Thanks for watching.

If you've owned your h2o softener for a few years or more you may discover some dark stains near the water line in the alkali (salt) tank. Y'all guessed it,that's mold. It'southward a good idea to clean that out so your water softener has a squeamish, fresh kickoff.

Mold Inside Water Softener Brine Tank

Cleaning out your alkali tank is a fairly piece of cake process, especially if you have a two-piece water softener with a Clack valve similar this one! It should be done any time you start to see dark mold spots building up on the inside of your brine tank.

Start past planning alee. You volition want to schedule this job for when you have a minimal amount of salt in the tank. If you're about to add together table salt to your brine tank and y'all notice these blackness lines, consider setting that salt aside and tackling a squeamish cleanup first! And you definitely don't want to try this when yous take a salt clog!! If you detect yourself stuck with a salt clog, take care of that first before trying to tackle the cleaning job.

Cleaning Pre-Make full vs Post-Fill Brine Tanks

Water Softener Salt Tablets

Most water softeners fill the alkali tank with water every bit the last cycle of the Regeneration process, if that is the instance with yours, you will see h2o in the bottom of the brine tank, intermixed with the softener salt. That is known as a Postal service-Fill up h2o softener. If you don't see any water in the bottom of your brine tank, yours is a "Pre-Fill" water softener, which is the easiest to clean.For a Pre-Fill up water softener, all you lot need to do is remove the salt, clean the within of the brine tank, and then return the salt.

For a "Post Fill" softener, which fills the brink tank after each regeneration cycle, you're going to need a few additional steps to remove the water AND the common salt from the brine tank before y'all can clean information technology properly.

Steps to Clean Your Brine Tank

Cleaning Your Water Softener Brine Tank

Step 1 – Remove the H2o from the Alkali Tank

The commencement step is to remove the water from the brine tank. You can do this by using a wet/dry out Shop Vac, or y'all can let the water softener do that for you.

To remove the brine in a "Post Fill up" water softener with a Clack valve, start past forcing your h2o softener into a regeneration. On modernistic water softeners, this is easily done by holding down the regen button until the motor starts upwards.

Y'all want to go your water softener into the brine bicycle so information technology starts to suck out the water in the brine tank, which is the second bike so press the Regen push once again and the word Brine will appear on the display. You may need to expect until the first cycle starts to count downwardly before existence able to printing the Regen button again to skip this cycle.

Note the inaugural time on the display, as that is normally an indication of how much time you lot have so that yous tin can go and do something else while the alkali is being removed from the brine tank.

Once the h2o is out of the brine tank, place the water softener into bypass then the system doesn't refill the brine tank before yous're finished.

Step 2 – Remove the Common salt from the Alkali Tank

Once all the water is gone from the brine tank, yous'll too want to get the remaining salt (if any) out of the style so you tin can give your brine tank a thorough cleaning.

You should be able to scoop the table salt out of the brine tank and place it in a plastic saucepan. Simply brand sure to wear safe gloves while doing this, equally the pure common salt tablets tin exist quite harsh on the peel.

Step 3 – Cleaning the Brine Tank

If yous take a 2-piece h2o softener, yous can either clean the brine tank in place or disconnect information technology and take information technology outside where it might be easier to clean. With a one-piece water softener, y'all have no choice merely to make clean it in place. Yous tin can apply dishwashing soap to launder clean information technology out, or – if the mold is quite pregnant – you lot may need a mold eliminator. Once the brine tank is spic and span, brand sure to rinse it thoroughly to remove whatsoever soap residuum.

Remove the cleaning water by either dumping it out or with a shop vac. Do NOT use the regen wheel to attempt to suck the h2o out of the brine tank over again, as you lot don't want that water entering your softener system.

Pace 4 – Filling and Restarting Your System

If you take disconnected your alkali tank, first by reconnecting it to the system. Then you'll want to add a couple of new numberless of table salt. We don't usually recommend putting the old common salt back into the softener, because y'all want everything to have a nice, clean, fresh offset.

Add together iii gallons of water to the salt and then manually scroll through the Regen cycles to become information technology back into service, if non already there. Have water softener out of featherbed and put it back into service.

Fix your system to "Regen Today" then the water softener will Regen at its pre-set Regen time and information technology will become through the whole procedure, make clean itself, and brand certain y'all are back at 100% softening capacity by the side by side 24-hour interval.

Your Brine Tank is Clean, Fresh and Set to Soften Your Water

Clean Water Softener Brine Tank

Nobody likes dirty water, especially inside their domicile. Make sure to inspect the inside of your brine tank each time y'all add salt to check for tell-tale signs of mold. If you lot see them, clean them out to make sure your system is running at its all-time.

Let's Fix Your Water